VCC4_v7s1 10/04/2004
This is the last release of the VCC software and includes the underscan feature.

Galaxy V2.09 01/07/2005
This latest version of Galaxy uses C++ instead of JAVA enhancing the speed at which the presets load. Please make sure you have the latest firmware dated 11/29/2004 before using this version. All modules shipped after 01/07/2005 will include the latest firmware update.

11/29/2004 Firmware Update
There are three files in the Zip file, please use only the file that applies to the unit you have. Also you will need to make a special cable for this update to work. Please call our technical support line for further instructions.

Galaxy V2.05 09/04/2004
This is the last version of Galaxy before it was ported over to C++. Please use this version if you do not have the latest firmware update. Please make sure the firmware on your module is dated 10/04/2004 before using this version of Galaxy.

10/04/2004 Firmware Update
There are three files in the Zip file, please use only the file that applies to the unit you have. You can load this update directly through Galaxy V2.05.

Galaxy V2.03 06/02/2004
Please make sure the firmware on your module is dated 06/02/2004 before using this version of Galaxy.

06/02/2004 Firmware Update
There are three files in the Zip file, please use only the file that applies to the unit you have. You can load this update directly through Galaxy V1.06.

NDVI V3.08 05/02/2003
This is the last release of the NDVI software. It is used for 1st generation 4-Cast modules (non IP).

IO Networks USB-RS485 Converter
This device is for users who purchased MCC modules without an Avitech controller. The communication protocol for the majority of the MCC and VCC modules are RS485 so in order to control it with a PC or laptop, this converter is required. Please download the drivers and if you need support on this product or you need drivers for Windows 98SE or earlier, please visit www.ionetworks.com and search for Edgeport/2i.

Moxa CI-134
The Moxa CI-134 serial communication card is used in all versions of the Avitech controller. Each card has four ports that are set to RS485 by default. They can be changed to RS422 as well. Controllers can have up to two cards and these drivers are provided for reinstallation of single card controllers. If you have two cards, please call our technical support for instructions. If you need documentation or Windows 98SE drivers, please visit www.moxa.com and search for CI-134.

Colorgraphic Xentera GT4
The Xentera GT4 graphics card is used in all Avitech controllers purchased after October 2004. To identify the card, look for four miniature USB like ports with a screw hole above each port. If you open the controller, the print circuit board in the controller should be red in color. This driver is provided for you in case you need to reinstall the card. If you have a controller with two graphics cards, please install the first card and the drivers before installing the second card. For drivers and manuals, please visit the Colorgraphics website..

Matrox G200 & G450 MMS
The Matrox G200 and G450 graphics cards were used in controllers that were shipped before October 2004. These included controllers with Windows 98SE. Please make sure that when you resintall these drivers, they show up as G200 and G450 Multi-Monitor and not millenium G200. If you have a controller with two graphics cards, please install the first card and the drivers before installing the second card. For all drivers and manuals, please visit the Matrox website. Remember to download only Windows Certified Drivers.

CPU Card
The CPU card is the motherboard on the Avitech controller, there have been 4 different versions and we currently use the SAGP-865EV. Previous versions include the Rocky 4786, Rocky 4782, and Rocky 3782. The three main drivers you will need is LAN, VGA, and Chipset drivers. Please verify the version you have and download the drivers and manual from the IEI website.